







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Santa Ana, CA: What It Costs and How It’s Built
An iron fence in Santa Ana typically runs $3,500 to $9,000 for a standard residential run, and most jobs are measured, permitted, fabricated to size and set in concrete over three to five working days once the design is signed off. That price covers removal of an old fence, footing work, the iron panels and posts, finish, and gate hardware. Homes along the Lacy and downtown blocks often land at the higher end because tight side yards, original clay sewer laterals and historic-frontage rules change how the work gets sequenced. Call (833) 749-3967 for a free on-site estimate.
How We Build an Iron Fence in Santa Ana: The Stage-by-Stage Process

An iron fence is a fabricated product, not an off-the-shelf panel, so the sequence matters more than most homeowners expect. Here’s the real order of operations.
Day 1: Site visit and layout. We walk the property line, flag utility locations through the 811 service, and set the post spacing. Most residential runs break on 6- to 8-foot centers, and on narrow Santa Ana side yards the spacing sometimes shifts to keep a gate landing usable. This is when you decide whether the fence sits tight to the property line or a few inches inside it, which matters if a neighbor’s existing wall already crowds the line.
Day 2: Demolition and prep. Old fence comes out, footings get broken open or re-cut, and we confirm the grade. On the 1920s-1950s bungalows we work in across Santa Ana, footing discovery is the wildcard: sometimes there’s a clean curb, sometimes there’s a buried brick edge or a clay lateral you don’t want to pierce. We hand-dig near sewer laterals for that reason.
Day 2 to 3: Footings and post setting. Posts go into concrete footings sized to the fence height and wind load. Drive gates for a Santa Ana alley-load or townhome driveway need a heavier footing than a standard gate because they carry more weight and take harder use. Concrete cures overnight before anything racks against it.
Day 3 to 4: Fabrication and install. Panels and gates built to the measured dimensions get set, leveled and welded or mechanically fastened depending on the spec you chose. Gate hinges and latch hardware go on here. If you selected a rolling or swing gate, this is where the opener, track or pivot gets mounted.
Day 4 to 5: Finish, touch-up, walkthrough. We touch up welds and fastener heads, check every gate for swing and latch, and do the final walkthrough with you before we leave. Permits, where required, get scheduled for inspection around the footing and final stages. The finished job is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Your Santa Ana Iron Fence
Iron fencing isn’t one product. Here’s what actually drives the spec and the price, and who each option suits.
- Wrought iron (solid bar, forge-welded): the traditional pick, heavier gauge, custom built to dimension. It’s the most expensive per linear foot and takes longer to fabricate, but it’s the one that lasts decades and reads right on a Spanish Colonial Revival or Craftsman frontage.
- Tubular steel (steel tube profiles, assembled): a lighter and faster option that looks close to wrought iron from the street. It suits tighter budgets and is a good match for newer townhome infill where security and clean lines matter more than historic detailing.
- Aluminum fence: the lowest-maintenance choice, powder-coated, rust-proof, and available in black to mimic iron. We build it, but it doesn’t carry the same weight or security feel, so we’re honest about that trade-off.
- Finish: powder coat is standard and holds up in Santa Ana’s dry heat. A hot-dip galvanized base under the finish is worth the upcharge on lower-ground fence lines where seasonal winter rain pools.
- Configuration: walk gate, drive gate, double swing, rolling gate. Rolling gates solve tight driveway width on townhome and alley-load lots. Automating the gate with a rolling-code remote or keypad adds to the job and needs power routing planned before the concrete goes down.
- Height and picket spacing: 4-foot for a front corner accent, 5 – 6 foot for full property lines. If the goal is security rather than looks, tighter picket spacing and vertical spear finials matter more than the finish.
What an Iron Fence Costs in Santa Ana, CA

For a standard residential run, expect $3,500 to $9,000. Here’s how the number gets to the low end or the high end.
| Line item | Typical range |
|---|---|
| Wrought iron (solid) fence, installed | $6,000 – $9,000 |
| Tubular steel fence, installed | $4,000 – $7,000 |
| Aluminum iron-look fence, installed | $3,500 – $6,500 |
| Walk gate (single, hinged) | $600 – $1,800 |
| Drive gate (double or rolling) | $1,500 – $4,500 |
| Old fence removal and haul-away | $300 – $900 |
| Historic-preservation or plan review | varies by scope |
Four things push the price:
- Linear footage and gate count. The single biggest driver. A 60-foot property line and a 120-foot property line aren’t the same job.
- Material grade. Solid wrought iron runs roughly 40 – 60% more than tubular steel for the same run.
- Site conditions. Hand-digging near clay sewer laterals, breaking out an existing concrete curb, or working in a tight side yard with no alley access adds labor.
- Automation and permits. A powered gate with rolling-code remotes adds cost and electrical routing. Historic-preservation review on a pre-1940 downtown or Lacy-area frontage can add a plan-check step.
Your written estimate is line-itemized: fence, gate hardware, footing concrete, removal, permit fees where applicable. What’s typically not included is electrical work for an automated gate opener (we coordinate with an electrician) or major landscape repair after footing excavation. Upfront pricing means the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Ana Homes Specifically Do to an Iron Fence Job
Santa Ana has an unusual construction reality: a large stock of pre-1950s bungalows and Spanish Colonial Revival homes, many still carrying original clay sewer laterals and unreinforced masonry, sitting blocks away from aggressive infill townhome construction under the city’s adaptive-reuse and SB 9 lot-split rules. For an iron fence, that means two things. First, in the historic downtown and Lacy-area blocks, structural changes near a frontage can trigger historic-preservation review, so we check that early rather than after the concrete is poured. Second, on the newer infill townhomes, you get tight side yards, alley-load driveways and shared property lines, which is where a rolling gate and a carefully set layout solve problems a standard swing gate can’t.
The dry Santa Ana wind events that come off the foothills also matter: iron doesn’t rot or burn, which is exactly why homeowners on the eastern edges of the city choose it for defensible-space lines. Seasonal winter rain is the other factor. Poor drainage on aging bungalows drives footing design, and a galvanized base coat under the finish is worth it wherever the line sits low. We work the 92799, 92701, 92735 and 92707 ZIP codes routinely, and homeowners often pair an iron fence with Patios, Walkways & Pool Decks in Santa Ana to tie the yard together, or with ADU Design & Permitting in Santa Ana when a lot split is also in the works. For the wider scope, see Fence Installation in Santa Ana, or view our Fence Installation service hub.
Serving Santa Ana, CA – Our Local Coverage Area
We serve Santa Ana and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Santa Ana

Most residential iron fence jobs take three to five working days from demolition to walkthrough, with fabrication of custom panels happening in parallel. Tight side-yard work and historic-review frontages can stretch that a day or two. Call (833) 749-3967 for a free estimate with a real timeline.
Fence permits depend on height, location and whether the property sits in a historic district, and taller fences or frontage work often need one. We pull the permit and manage inspection as part of the job, and we flag any historic-preservation review early. Call (833) 749-3967 to confirm what your property needs.
In most cases yes. The work stays above the footing line, and we hand-dig near clay sewer laterals to avoid piercing them. Only an automated gate that needs power touches electrical. Call (833) 749-3967 to walk through your site.
Expect $3,500 to $9,000 for a standard residential run, with the range set by footage, material grade, gate count and site conditions. Call (833) 749-3967 for an exact line-itemized quote; estimates are free.
Every iron fence and gate we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship, footing and hardware installation. Call (833) 749-3967 to schedule your free estimate.
Get a Free Iron Fence Estimate in Santa Ana
We’ll come to your property, measure the actual run, flag utility and historic-review issues, and hand you a line-itemized written estimate for your iron fence in Santa Ana, usually within a few days of the visit. No change orders, no surprises. We cover Santa Ana and the surrounding neighborhoods. Calls are answered by a live person, 24/7. Call (833) 749-3967 to schedule your free estimate.
Written by the team at Groundwork Construction Co.












