







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Tustin: What the Job Actually Costs and How Long It Takes
Replacing a vanity, re-tiling a bathroom floor or shower surround, and swapping out fixtures in Tustin usually runs $9,000 – $28,000 for a full tear-out and rebuild, or $800 – $3,000 if it’s just a vanity swap. A vanity-and-tile package takes 4 – 8 working days on site, plus a few more for permit review if plumbing moves. Call (833) 749-3967 for a free on-site estimate with a written, line-item quote before anything gets demoed.
How we handle vanities, tile and fixtures, stage by stage

This isn’t a one-day job dressed up as a remodel, and we don’t pretend it is. Here’s the actual sequence, what we’re doing each stage, and where you make the call.
Stage 1: On-site measure and spec lock (day 1, about 90 minutes)
We measure the vanity alcove, check the shutoffs, confirm whether the drain and supply lines stay put, and look at the subfloor under the existing tile. Tustin ranches from the 1950s and ’60s often have a plywood subfloor that’s sound but uneven, and that decides whether we’re laying a self-leveling compound or a backer board membrane. This is the day you pick your vanity width and finish, the tile and the fixture trim so nothing sits on backorder when demo starts.
Stage 2: Demo, shutoffs and rough-in (days 2 – 3)
We pull the old vanity, take out the tile and the substrate under it, and open the wall where the plumbing is. If you’re moving the sink location or changing from a single to a double vanity, this is when the rough plumbing and any new GFCI outlet happen, and the inspection gets scheduled. Keeping the drain where it is saves both time and money; moving it is a decision you’ve already made by now.
Stage 3: Waterproofing and tile setting (days 3 – 5)
We waterproof the wet zones before a single tile goes down. On shower walls and floors we use a bonded sheet membrane system like Schluter, which is the standard we hold ourselves to because it keeps water out of the framing for the life of the bathroom. Wall tile and floor tile go in on separate days so the setting beds cure properly. Grout and caulk come last, and caulk at every change of plane, not grout, so the joints move instead of cracking.
Stage 4: Vanity, fixtures and trim-out (days 5 – 6)
The vanity cabinet gets set and shimmed level, the countertop drops in, the faucet and drain connect, and the toilet goes back. We set the mirror, the lighting and the accessories. You’ll have already chosen the vanity and fixture finish at spec lock, so this stage is install, not shopping.
Stage 5: Final inspection and walkthrough (day 6 – 8)
We do our own punch walk before the city inspector arrives, because it’s easier to catch a crooked trim piece on our schedule than theirs. Then you walk it with us, we note anything that needs attention, and it gets fixed under the 730-Day Done Right Promise. Anything we touched is covered, start to finish.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The vanity, tile and fixture options you’ll actually choose between
Most of the decisions that move your budget happen before demo, so here’s the honest trade-off on each.
- Vanity cabinet material: Plywood boxes with a painted or stained finish outlast particleboard, especially in a bathroom that sees daily steam. A stock vanity is quick and affordable; a semi-custom or KraftMaid build gets you the exact width and door style to fill an odd alcove gap.
- Vanity top: Cultured marble is the value pick and holds up fine. Quartz (Cambria is one we install often) resists staining, scratching and heat far better, at a higher material cost. Granite and butcher block sit in between, with butcher block needing re-oiling.
- Floor tile: Porcelain is the workhorse for a Tustin bathroom, dense, low-absorption and hard to stain. Natural stone looks richer but needs sealing and more careful cleaning.
- Wall and shower tile: Large-format tile means fewer grout lines to keep clean and a faster install. Mosaic and small formats give you more design room but more grout to maintain.
- Fixtures: A mid-range Grohe or Sterling faucet is a sound, water-efficient choice that won’t need replacing in a few years. A builder-grade faucet costs less up front and often gives up sooner. Same logic applies to the shower valve and drain trim.
- Waterproofing system: A bonded membrane like Schluter behind the tile is the difference between a shower that lasts twenty years and one that leaks into the wall in five.
- Lighting and vent fan: A properly sized exhaust fan matters in Tustin’s dry but humid-bathroom reality; undersized venting is a top cause of failing paint and mold at the ceiling line.
What Vanities, Tile & Fixtures costs in Tustin, CA

A full tear-out and rebuild of vanities, tile and fixtures in Tustin runs $9,000 – $28,000. A vanity-only swap lands at $800 – $3,000, and a shower or tub-to-shower replacement, which has its own dedicated page, runs $3,000 – $12,000 depending on scope. Those are real ranges, not teasers, and here’s what drives a job toward either end.
- Size and layout: A single-vanity guest bath stays near the low end. A double vanity with a longer tile run pushes the number up fast.
- Existing condition: Sound plumbing and a flat subfloor mean the job flows. Original galvanized supply lines, a rotted subfloor, or a slab leak discovered at demo adds real money and days.
- Moving plumbing or electrical: Relocating a drain or adding a new circuit is where budgets move the most, since it requires rough-in work and a permit.
- Material grade: A cultured marble top and porcelain floor sit near the low end. Quartz counters, large-format stone-look tile and premium fixtures push toward the high end.
- Permit scope: A cosmetic swap of the same-size vanity and tile may not need a permit. Moving plumbing, adding a circuit, or changing the wet-wall layout does, and the inspection adds a day or two to the schedule.
A written estimate from us lists the materials, labor, permit and disposal line by line, with upfront pricing so the number on the page is the number you pay. What it typically excludes: any hidden damage behind the wall that only shows once it’s opened. If we find it, we stop, show you, and quote the fix before touching it. We treat the wider bathroom as one plan when it’s part of a full Bathroom Remodeling in Tustin, and we handle Bathroom Remodeling across our service area the same way.
See the difference
Before
After
Before
After
Before
AfterWhat Tustin homes specifically do to this job
Tustin is a city of two eras, and the vanities, tile and fixtures job changes with each. In the 92780 ranches, built mostly from the 1950s through the ’70s, we regularly find original galvanized supply lines that have narrowed with age, so the water pressure at the new vanity is weak until we replace them. Those same homes sit on plywood subfloors that have flexed under the old tile, which we correct before any new floor goes down. In the 92782 homes of Tustin Ranch and Columbus Square, the stock is newer, 1980s-to-2000s Mediterranean tract houses, and the failure mode is different: the original builder-grade vanities and tile tend to look tired rather than be broken, so the job is cosmetic and predictable. Any project inside the old MCAS Tustin footprint draws extra environmental and historical review, and it’s worth confirming permit scope before demo on older ranches, because a cosmetic refresh is a different process than a rough-in change. We cover all of Tustin and explain the permit path up front so there are no surprises at inspection.
Serving Tustin, CA – Our Local Coverage Area
We serve Tustin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked questions about vanities, tile & fixtures in Tustin

A full tear-out runs 4 – 8 working days on site, plus a few more days if a permit inspection is involved. A vanity-only swap is usually a single day. Call (833) 749-3967 and we’ll give you a schedule specific to your bathroom.
If you’re keeping the same-size vanity and the plumbing where it is, you often don’t need a permit. Moving the sink location, changing the drain, adding a GFCI circuit, or reconfiguring the shower does require one. We pull the permit and coordinate the inspection for you, and we tell you which case you’re in before we start.
Yes, and it’s the most common way we do this job. Replacing the vanity of the same footprint and laying new tile over the existing layout keeps the price near the low end of the range. If you want a double vanity or a shifted sink, that’s a bigger job and we quote it separately.
The full range is $9,000 – $28,000 for a tear-out and rebuild, or $800 – $3,000 for a vanity swap. Call (833) 749-3967 for an exact quote, and estimates are free.
Every job is backed by our 730-Day Done Right Promise, so if anything we installed fails, we make it right. It covers the vanity, tile, waterproofing and fixtures we install, with terms spelled out in writing.
Get a free estimate for vanities, tile & fixtures in Tustin
Call (833) 749-3967 to schedule a free on-site estimate. You’ll get a written, line-item quote with upfront pricing, a realistic schedule, and a clear answer on whether your job needs a permit. Homes in Tustin often pair this with tile work outside, and if you’re thinking about the roof too, ask about Tile Roofing in Tustin or Specialty Roofing in Tustin while we’re there. One call, one plan, no surprises.
Written by the team at Groundwork Construction Co.












