







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Santa Ana: What It Takes and What It Costs
Metal roofing in Santa Ana runs $15,000 to $40,000 for a typical single-family home, and most installs take three to six days of on-site work once the panels are delivered. The number that actually moves is roof size, panel system, and how much of the old roof and sheathing gets torn off. Santa Ana’s mix of 1920s bungalows and postwar stucco homes means we see both straightforward overbuilds and full tear-offs on the same block. Call (833) 749-3967 and we’ll walk your roofline with you and put a real number on paper.
How a metal roof goes on, stage by stage

Metal isn’t a product you can slap over whatever’s there and walk away from. The sequence matters more than the panel itself, and here’s how it runs when we do the work.
Stage 1: Tear-off and deck inspection (one to two days)
The old roofing comes off down to the sheathing. On a 1930s Lacy-area bungalow, that’s where we find out whether the skip sheathing under the original clay holds square or needs replacement boards, and you’ll get a written change order before we touch it. Solid decking means metal goes down tight. Punky deck means we fix it now or it telegraphs through the panels later.
Stage 2: Underlayment and ice-and-water membrane (half a day)
We run a high-temp synthetic underlayment across the field and a self-adhering membrane in the valleys, along the eaves, and around any penetration. This is the layer that keeps a Santa Ana roof dry through winter rain even if a panel ever gets dented or lifted. You choose the underlayment grade here; it’s a modest line item and it’s worth the better one.
Stage 3: Flashing, trim, and penetrations (one day)
Ridge cap, drip edge, valley metal, and boots around every vent. Get this wrong and a metal roof leaks exactly like an asphalt roof. You decide at this stage whether you want a heavier gauge drip edge and a color-matched ridge vent, or whether you’ll take the standard finish.
Stage 4: Panel installation (one to two days)
Panels go up in courses, fastened with exposed or concealed clips depending on the system you picked. Your decision here is the fastener and clip spec, which we lock in at the estimate, not mid-job. Concealed-fastener systems take longer because more alignment work goes into them.
Stage 5: Final inspection and walkthrough (half a day)
We check every seam and penetration, clean the gutters of debris, and walk the roof with you. Your last decision is whether to add a snow-guard style panel or skip it; in Santa Ana most homeowners do. The written workmanship warranty gets handed over at this walkthrough, backed by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The metal roof options you’ll choose between
- Standing seam vs. exposed fastener. Standing seam hides the fasteners under raised seams and handles expansion better on our swings between hot days and cool mornings. It costs more and looks cleaner. Exposed-fastener panels run less, install faster, and need periodic screw checks. Standing seam suits a home you plan to keep.
- Panel gauge. Lighter 29-gauge panels suit budget work and light-duty sheds. 26-gauge is the residential standard and holds up under foot traffic. 24-gauge is heavier and worth it on a high-wind or foothill-edge roof.
- Finish: Kynar (PVDF) vs. polyester paint. Kynar holds color and chalk resistance far longer under harsh UV. Polyester is cheaper and fades sooner. Pay for Kynar on a roof you’ll live under for decades.
- Substrate: steel vs. aluminum. Steel is stronger and cheaper; aluminum resists corrosion and weighs less. For most Santa Ana homes, steel is the practical pick.
- Color. Light colors reflect heat and stay cooler under the roof in summer. Dark colors read traditional on a Spanish Colonial Revival but soak up sun. Your HOA may narrow the palette; check before you pick.
What Metal Roofing costs in Santa Ana, CA

Residential metal roof installation in Santa Ana runs $15,000 to $40,000. Where a given job lands depends on these variables:
- Roof size and pitch. A larger footprint at a steep pitch takes more material and more labor hours. Low-slope roofs run cheaper per square.
- Existing roof condition. A clean tear-off of a sound deck sits at the low end. Rotted sheathing, skip sheathing, or two layers to strip pushes it up.
- Panel system. Standing seam with concealed fasteners sits higher than exposed-fastener panels of the same gauge.
- Gauge and finish. Heavier steel and Kynar finishes cost more up front and last longer.
- Flashing and penetration count. Chimneys, dormers, skylights, and complex valleys add labor and material.
- Permit scope. A simple re-roof permit costs less than one that pulls in structural review.
A written estimate should itemize tear-off, deck repair allowance, underlayment, flashing, panels, fasteners, and permit. What it typically doesn’t include: any hidden structural repair found after tear-off (quoted separately as a change order), gutter replacement, or painting the fascia.
See the difference
Before
After
Before
After
Before
AfterWhat Santa Ana homes specifically do to this job
Santa Ana’s housing stock runs 1920s – 1950s California bungalows and Spanish Colonial Revival homes, plus postwar stucco tract housing, and that split changes the job on nearly every street. Over near downtown and the Lacy area, pre-1940 bungalows frequently sit on original redwood framing and skip sheathing, and any structural change during the re-roof can trigger a historic-preservation review before we proceed. East toward the foothill edge, Santa Ana wind events drive wildfire-risk and defensible-space requirements that shape roof material and venting choices. In 92705 and the surrounding ZIPs, winter rains are the test: we see old drainage systems and low-slope sections on aging bungalows fail first, which is why the underlayment detail matters as much as the panel. Across the 92711, 92702, and 92712 ZIPs, infill townhomes and SB 9 lot-splits sit next to historic homes, so we plan access and staging around tight parcels and alley loads. Permits and inspections are handled by us, and we pull them. If this job is part of a broader scope, our Roofing in Santa Ana page covers the full picture.
Serving Santa Ana, CA – Our Local Coverage Area
We serve Santa Ana and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Metal Roofing in Santa Ana

Most Santa Ana metal roofing jobs run three to six days of on-site work once panels are delivered, with the range driven by roof size, panel system, and how much of the old roof and deck gets torn off. Call (833) 749-3967 for a scheduling estimate on your specific roof.
Yes, we pull the permits and handle the inspections. Santa Ana’s older bungalows near downtown and Lacy can require structural review before re-roofing, and we flag that at the estimate rather than surprise you later. Call (833) 749-3967 to confirm what your property needs.
It depends on the deck and local code; many metal systems can go over a sound existing roof, while others need a full tear-off. On a 1930s bungalow we’ll inspect the sheathing first, and we’ll tell you honestly which path is right. Call (833) 749-3967 to schedule an inspection.
Residential metal roofing in Santa Ana runs $15,000 to $40,000 depending on roof size, panel system, materials, and existing deck condition. Call (833) 749-3967 for a written, itemized quote and free estimate.
Every metal roof we install is backed by our 730-Day Done Right Promise, on top of the manufacturer’s product warranty. Call (833) 749-3967 to review your options before you commit.
Homeowners weighing a metal roof often pair the decision with our Roofing service, and many upgrade their home’s exterior at the same time with Window Replacement in Santa Ana or Impact Windows & Doors in Santa Ana. We also serve the surrounding communities on our Santa Ana service-area page.
Get a free metal roofing estimate in Santa Ana
We’ll walk your roofline, check the deck and underlayment, and hand you an itemized quote with no hidden line items. The number you see is the number you pay. Our calls are answered by a live person 24/7, and every technician arrives background-checked and in uniform. Call (833) 749-3967 to schedule your free estimate for Metal Roofing in Santa Ana.
Written by the team at Groundwork Construction Co.












