







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wood Fence in Newport Beach, CA: What It Costs and How Long It Takes
A wood fence in Newport Beach, CA typically runs $3,500 to $9,000 for a standard residential run, with most jobs finished in two to four days once materials are on site. That range covers removal of the old fence, new posts set in concrete, and cedar or pressure-treated boards. Larger lots, gates, and tight coastal access push the number toward the top. Call (833) 749-3967 for a free on-site estimate.
How We Build a Wood Fence, Start to Finish

We don’t hand you a bid and disappear for three weeks. Here’s the actual sequence, so you know what’s happening on your property and when.
Day 1: Walk the line and mark it
Before anything gets dug, we walk the property line with you and confirm where the fence lands. If the line is unclear, we recommend a survey first, and we’ll tell you straight when one is needed. We also check for irrigation lines, low-voltage lighting, and gas or water stubs buried along the path. On older Newport Beach lots, that scan regularly turns up a sprinkler run or a stub from a long-removed spa. Marking takes an hour. Finding a line with a shovel later costs days.
Day 1 to 2: Demo and haul-off
Old fence comes down, posts get pulled, and everything goes to the dumpster in one trip. A typical 150-foot run takes half a day to a full day to remove. If the posts were set in concrete, we break that out too. You don’t touch a shovel. The only decision on your end is whether you want any of the old fencing saved for firewood or reuse.
Day 2 to 3: Posts set and cured
We dig post holes to depth, set them in concrete, and let them cure before boards go on. Skipping the cure is the most common shortcut in this trade, and it’s why fences lean within two or three years. Holes get dug to roughly a third of the post’s above-ground height, which on sandy or fill-heavy lots here often means a deeper dig than a standard build. Your decision at this stage: post spacing (we default to 8 feet, tighter on taller fences) and the post material itself.
Day 3 to 4: Rails, boards, and gate
Rails go on, then pickets, then the gate. A single walk gate or a double drive gate both get built and hung here, with hardware installed and the swing tested. Pickets get set at your chosen height and cap style. This is the stage where the fence starts looking like a fence.
Final day: Stain, cleanup, walkthrough
If you chose a stain or sealer, it goes on after the wood has had time to dry. We clean the site, walk you through every run, and hand over the written workmanship terms. Any punch-list item gets addressed before we pack up.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Wood Fence Options You’ll Actually Choose Between
Most homeowners get tripped up here, so let’s make the trade-offs plain. The species of wood, board height, and style all move both the price and how the fence holds up against salt air.
- Cedar vs. pressure-treated pine. Cedar is the better-looking, longer-lasting choice in a coastal climate and resists rot and insects naturally. It costs more, often 20 to 30 percent above pine. Pressure-treated pine is the budget pick; it’s fine for a back-of-lot privacy fence but will need refinishing sooner and can warp in constant marine humidity.
- Dog-ear vs. flat-top pickets. Dog-ear (the angled-top board) is the most common and sheds water off the cut edge. Flat-top reads more modern and pairs well with mid-century peninsula homes. Style choice is personal and doesn’t change labor much.
- Board height. Most residential privacy runs sit at 6 feet. Going to 7 or 8 feet adds material and, in some cases, engineering, plus it matters for your neighbor’s sun exposure and for how the fence reads from the street.
- Stain and sealer. A penetrating stain or marine-grade sealer protects the wood and slows graying. It adds a line item to the estimate but usually pays for itself in longevity. Skip it and you’ll be refinishing within two years.
- Stainless or coated fasteners. Cheap galvanized nails rust through fast in salt air. We default to stainless or marine-grade hardware on this coast. It’s a small line item with an outsized effect on how long your fence stays solid.
If your project widens into a full property boundary redesign, our Fence Installation in Newport Beach page covers the wider scope, and homeowners often pair a new wood fence with Paver Driveways in Newport Beach when the front of the house is getting redone at the same time.
What a Wood Fence Costs in Newport Beach, CA

Plan on $3,500 to $9,000 for a wood fence in Newport Beach. That’s the real, market-calibrated range for a standard residential job including removal of the old fence, new posts set in concrete, six-foot cedar or pressure-treated boards, and cleanup. The fence is a modest project with a lot of variables under the hood, though, and five of them move the price most.
- Total linear feet. The single biggest driver. A 100-foot run sits near the low end; a 250-foot perimeter pushes it toward the top.
- Condition of the existing fence. Posts set in concrete that need breaking out add labor. So does hauling heavy debris off a tight coastal lot where a dumpster can’t sit close.
- Wood species and board grade. Cedar over pressure-treated pine is the clearest step-up in both quality and cost. Rough-sawn or premium-grade cedar adds more.
- Gates and hardware. Each walk gate or drive gate is priced as its own build. A self-closing or heavy-duty driveway gate adds to the total.
- Permit and lot-line scope. Most residential wood fences under six feet don’t need a city permit, but height, setback, and lot-line rules vary and coastal or HOA-restricted properties can require review. If a permit is needed, we handle pulling it and passing inspection.
What’s included in a written estimate: removal and haul-off, posts and concrete, rails and boards, gate, labor, and cleanup. What’s typically not included unless you ask: staining (often priced separately), a lot-line survey if one is needed, and any repair to a shared property line. The number you see on the written quote is the number you pay. No change-order surprises once the work starts.
See the difference
Before
After
Before
After
Before
AfterWhat Newport Beach Homes Specifically Do to This Job
Newport Beach isn’t Irvine, and handling fencing here takes local knowledge. The salt air and constant morning marine layer are the first thing we plan around. Metal fasteners, hinges, and gate hardware corrode fast, so we spec stainless or marine-grade hardware by default on this coast. Those choices separate a fence that still swings cleanly in year ten from one that rusts stiff in year three.
The housing stock matters just as much. On the peninsula and around Balboa Island, we’re often working around older properties where the fence line runs close to aging infrastructure, and finding a sprinkler system or an old utility stub is routine. In Dover Shores and on the ocean side, properties carry both the city’s bayfront and oceanfront zoning overlays and, in many cases, California Coastal Commission conditions, so fence height, setback, and appearance can require design review or HOA sign-off before a single post goes in. We help you find out what applies on your lot before we dig. Out with the wider Newport Beach work, this is the kind of check we do on every job.
Most fences here get built in dry, mild weather, which is a real advantage. But persistent coastal humidity and sandy, fill-heavy soil mean we dig deeper post footings and cure the concrete fully before boards go on. Skimp on either and you’ll be fighting a lean within a couple of seasons.
Serving Newport Beach, CA – Our Local Coverage Area
We serve Newport Beach and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Wood Fence in Newport Beach

Most wood fence jobs here take two to four working days from demo to final walkthrough. A short back-lot run of around 100 feet can wrap in two days; a full perimeter with gates runs three to four. Call (833) 749-3967 for a firm timeline on your property.
Most residential wood fences under six feet tall don’t require a city permit, but height, setback, lot-line, and coastal or HOA rules can change that on your specific property. We check what applies to your lot before we start and handle any permit that’s required, so an inspector never finds a surprise. Call us and we’ll tell you plainly what your lot needs.
Yes, in most cases. We scan for irrigation, lighting, and buried utility stubs before digging and route posts around confirmed lines rather than through them. Where a line genuinely blocks a post, we’ll show you the options and let you decide. Call (833) 749-3967 to talk through your layout.
A wood fence in Newport Beach typically runs $3,500 to $9,000, depending on linear feet, wood species, gates, existing-fence condition, and permit scope. That range includes removal, posts set in concrete, boards, hardware, and cleanup. Call (833) 749-3967 for an exact written quote, free of charge.
Every wood fence we build is covered by our 730-Day Done Right Promise: if something isn’t done right, we make it right. That’s one of the longest workmanship guarantees in the residential space, and it’s in writing. Call us to review the terms before you commit.
Get a Free Wood Fence Estimate in Newport Beach
Call (833) 749-3967 to schedule a free on-site estimate for your wood fence in Newport Beach. We’ll walk the property line with you, confirm what your lot allows, and hand you a written line-item quote with no surprises. Calls are answered by a live person, and our background-checked, uniformed technicians show up on time. Reach out today and we’ll get your project priced.
Written by the team at Groundwork Construction Co.












