







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Irvine, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Irvine, CA typically runs $3,500 – $10,000 and takes 5 to 10 working days from demo to final inspection. The job means removing the tub and its surround, reworking the drain and waterproofing to a code-compliant shower pan, and finishing with tile or a prefabricated wall system. Condos and townhomes with an HOA add a review step before work starts. Call (833) 749-3967 for a free on-site estimate.
How We Run a Tub-to-Shower Conversion, Stage by Stage

Every conversion follows the same sequence, and knowing it in advance is what keeps a homeowner from getting surprised mid-project. Here’s what actually happens.
Stage 1: Measure, scope, and HOA or city review (days 1 – 3, before any demo)
We measure the alcove, check the drain location, and confirm what the wall framing looks like behind the tub surround. In an Irvine condo or townhome, this is when we pull the association’s alteration form and material palette so the finish selections get approved on the front end rather than stalling the job later. You’ll make two decisions here: shower size (standard 60-inch alcove vs. a wider custom pan) and whether we’re tiling or setting a prefab system.
Stage 2: Demolition and rough-in (days 3 – 5)
The old tub, valve trim, and surround come out. If the drain is off-center or the valve is a two-handle relic, this is where the plumbing gets corrected. We open the wall enough to inspect for the water damage that tub surrounds hide, then reframe or sister any soft studs. Anything that touches the drain or valve gets permitted work, so a rough inspection happens before the wall closes.
Stage 3: Waterproofing and pan (days 5 – 7)
This is the stage that separates a shower that lasts from one that leaks into the ceiling below in three years. We set a sloped pan, apply a bonded waterproof membrane or a formed shower base, and tape and coat every seam. You’ll pick the pan material here: a tiled mud-set floor (best look, highest cost), a solid surface base, or an acrylic base (fastest, lowest cost, more flex underfoot).
Stage 4: Tile, walls, and glass (days 7 – 9)
Wall tile, a niche if you want one, and any accent band go up, then the glass panel or door gets templated and installed. Tempered glass is measured after tile is set, so there’s a two-to-three-day lag between the last tile and a finished enclosure. This is when the biggest visual choices land, and where material grade most directly moves your final number.
Stage 5: Final inspection and walkthrough (days 9 – 10)
We test the drain, check the slope with a level, verify the valve stops, and run the final inspection. You get a walkthrough with the waterproofing and pan warranty in writing. Our work is backed by the 730-Day Done Right Promise, so if a seam or a drain line isn’t right, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make Between
Most of the price spread on a tub-to-shower conversion comes down to four decisions. Here’s the honest trade-off on each.
- Prefab wall system vs. tile. A prefab acrylic or solid-surface surround installs in a day, cleans easily, and costs $1,500 – $3,000 less than tile. Tile gives you a real designer finish, holds resale value in Irvine’s tract resale market, but adds 3 – 4 days and $2,000 – $4,500 in labor and material.
- Shower base type. Acrylic base: fast, light, $400 – $900. Solid surface: mid-range, no grout lines at the floor, $800 – $1,600. Mud-set tile floor: best look, custom sizing, $1,500 – $3,000 and the slowest to complete.
- Glass. A framed sliding door keeps cost and complexity down. A frameless fixed panel looks cleaner but needs framing backing and adds roughly $600 – $1,400 to the job in Irvine.
- Valve and trim. Replacing a tired two-handle valve with a single-handle pressure-balance valve is best practice and a code improvement; brand-name trim like Kohler sits comfortably in the mid-range, and we carry it in our partner catalog.
- Niche and bench. A recessed niche adds $200 – $500. A built-in bench adds structure, $500 – $1,200, and only makes sense on a wider custom pan.
What Tub-to-Shower Conversion Costs in Irvine, CA

Plan on $3,500 – $10,000 for a tub-to-shower conversion in Irvine, with most tract-home alcove jobs landing around $5,000 – $7,000. The low end is a standard 60-inch alcove, an acrylic wall system, a prefab base, and an existing valve and drain that don’t need moving. The high end is a wider custom shower, tiled walls and floor, frameless glass, a relocated drain, and HOA-mandated materials.
Five things move the number:
- Size and layout. A standard alcove keeps framing costs predictable. A wider or offset shower adds structure and glass cost.
- Existing condition. Rot behind a surround or a tub that sat on a bed of mortar can add a day of demo and repair.
- Moving plumbing or electrical. Relocating the drain or adding a light in the shower tacks on $400 – $1,200 and shows up on the permit.
- Material grade. Tile selection swings the job more than anything else. Porcelain is affordable; natural stone pushes the top of the range.
- Permit scope. If the drain or valve changes, the permit and inspections apply. A finish-only swap is a lighter scope.
Your written estimate itemizes demo, rough-in, waterproofing, tile or surround, glass, and permit fees, so the number you see is the number you pay. Ask for the line-item quote in writing, not a verbal ballpark.
See the difference
Before
After
Before
After
Before
AfterWhat Irvine Homes Specifically Do to This Job
Irvine is a master-planned city, built almost entirely by the Irvine Company from the 1970s onward. That shapes a tub-to-shower conversion here in ways it doesn’t one city over in Santa Ana or Tustin. Most of the work we do sits in HOA-governed tract villages like Woodbridge, Northwood, and Turtle Rock, plus the newer Great Park-area builds. In those villages, every alteration runs through an architectural review committee before demo, so glass style, tile color, and even the visible door finish may have to match an approved palette. The city’s own strict design review adds a layer on top.
The housing stock matters too. These are 1970s-and-later tract homes and condos, not century-old structures, so what we typically find behind a surround is an off-center drain, a tired two-handle valve, and the occasional soft stud from a slow leak, not structural rot. The warm, dry Irvine climate makes for a fast, predictable schedule with almost no rain or freeze delays, which is why a ten-day conversion usually comes in on time.
If your conversion is part of a wider scope, we handle Bathroom Remodeling in Irvine as a single contract. We cover every ZIP in Irvine from 92606 to 92614. And homeowners often pair a bathroom refresh with exterior work, so we also do Metal Roofing in Irvine and Tile Roofing in Irvine on the same project schedule. Our Bathroom Remodeling service hub has the full scope if you’re weighing a bigger remodel against a conversion.
Serving Irvine, CA – Our Local Coverage Area
We serve Irvine and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Tub-to-Shower Conversion in Irvine

Most conversions take 5 to 10 working days, with the higher end for tiled walls and custom glass. The schedule stretches if your HOA requires a design review before work starts, which is common in Irvine’s planned villages. Call (833) 749-3967 and we’ll give you a realistic timeline for your specific unit.
Yes, if the drain, valve, or any plumbing is being changed, which is almost always the case when a tub comes out. Finish-only work may be lighter, but we confirm the scope with the city before demo so you don’t get caught in a failed inspection or a resale snag. We pull the permit and pass the inspection as part of the job.
Often, yes. If the existing drain and valve are correctly located and in good condition, we build the new shower pan around them and skip the rough-in move. It’s the cleanest, most affordable version of the job, and it’s what most Irvine tract-home alcoves allow.
In Irvine’s HOA-governed villages like Woodbridge and Northwood, yes. The architectural review committee typically wants your tile and glass selections and sometimes a visible exterior or door finish sample. We help you submit the paperwork and match the approved palette so the project doesn’t sit in limbo.
Every conversion is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If a seam or drain isn’t right, we come back and fix it. Call (833) 749-3967 and we’ll put the coverage in writing.
Get a Free Tub-to-Shower Conversion Estimate in Irvine
If you’re ready to price a tub-to-shower conversion in Irvine, call (833) 749-3967 for a free on-site estimate. We’ll measure the alcove, check the drain and valve, and walk you through the options and the trade-offs. You’ll leave the visit with a written, itemized number for your exact unit, and a live person answers the phone any hour of the day.
Written by the team at Groundwork Construction Co.












